Description

Description

The Arduino ESPLORA Joystick Photosensitive Sensor Board is a microcontroller board derive from the Arduino Leonardo. The Arduino ESPLORA Joystick Photosensitive Sensor Board differs from all preceding Arduino boards in that it provides a number of built-in; ready-to-use set of onboard sensors for interaction. It’s designed for people who want to get up and running with Arduino without having to learn about the electronics first. For a step-by-step introduction to the Esplora; check out the Getting Started with Esplora guide.

There are four status LEDs :

  • ON [green] indicates whether the board is receiving power supply
  • L [yellow] connect directly to the micro-controller, accessible through pin 13
  • RX and TX [yellow] indicates the data being transmit or receive over the USB communication

The board contains everything need to support the microcontroller; simply connect it to a computer with a USB cable to get started. The Esplora has built-in USB communication; it can appear to a connect computer as a mouse or keyboard, in addition to a virtual (CDC) serial / COM port. This has other implications for the behavior of the board; these are detail on the getting started page. You can find all the information you need to configure your board, use the Arduino Software (IDE); and start to tinker with coding and electronics.

Memory :

The ATmega32u4 has 32 KB (with 4 KB used for the bootloader). It also has 2.5 KB of SRAM and 1 KB of EEPROM (which can be read and written with the EEPROM library).

Input and Output

The design of the Arduino ESPLORA Joystick Photosensitive Sensor Board recalls traditional gamepad design with an analog joystick on the left and four push buttons on the right. The Arduino ESPLORA Joystick Photosensitive Sensor Board has the following onboard inputs and outputs :

  1. Analog joystick with central push-button two axes (X and Y) and a center pushbutton.
  2. 4 push-buttons laid out in a diamond pattern.
  3. Linear potentiometer slider near the bottom of the board.
  4. Microphone for getting the loudness (amplitude) of the surrounding environment.
  5. Light sensor for getting the brightness.
  6. Temperature sensor reads the ambient temperature.
  7. Three-axis accelerometer measures the board’s relation to gravity on three axes (X, Y, and Z).
  8. Buzzer can produce square-waves.
  9. RGB led bright LED with Red Green and Blue elements for color mixing.
  10. TinkerKit Inputs to connect the TinkerKit sensor modules with the 3-pin connectors.
  11. TinkerKit Outputs to connect the TinkerKit actuator modules with the 3-pin connectors.
  12. TFT display connector connector for an optional color LCD screen; SD card, or other devices that use the SPI protocol.

In order to utilize the total number of available sensors, the board uses an analog multiplexer. This means a single analog input of the microcontroller is shared among all the input channels (except the 3-axis accelerometer). Four additional microcontroller pins choose which channel to read.

USB Overcurrent Protection :

The Esplora has a re-settable poly-fuse that protects your computer’s USB ports from shorts and over-current. Although most computers provide their own internal protection, the fuse provides an extra layer of protection. If more than 500 mA is apply to the USB port, the fuse will automatically break the connection until the short or overload is remove.

Physical Characteristics :

The maximum length and width of the Esplora PCB are 6.5 and 2.4 inches respectively, with the USB and TinkerKit connectors extending beyond the latter dimension. Four screw holes allow the board to be attach to a surface or case.

Specifications and Features :

Microcontroller ATmega32u4
Operating Voltage 5V
Flash Memory 32 KB of which 4 KB used by bootloader
SRAM 2.5 KB
EEPROM 1 KB
Clock Speed 16 MHz
Lenght 164.04 mm
Width 60 mm
Weight 53 g

 

Package Includes :

1 x Arduino ESPLORA Joystick Photosensitive Sensor Board.
An internal link is any link from one page on your website to another page on your website. Both your users and search engines use links to find content on your website. Your users use links to navigate through your site and to find the content they want to find. Search engines also use links to navigate your site. They won’t find a page if there are no links to it.
There are several types of internal links. In addition to links on your homepage, menu, post feed, etc, you can also add links within your content. We call those contextual links. Contextual links point your users to interesting and related content. Moreover, they allow search engines to find out what content on your site is related and to determine the value of that content. The more links an important page receives, the more important it will seem to search engines. Therefore, good internal links are crucial to your SEO.

Additional information

Weight 0.1 kg

Reviews

There are no reviews yet.

Be the first to review “Arduino ESPLORA Joystick Photosensitive Sensor Board Support LCD in Pakistan”

Your email address will not be published. Required fields are marked *

three + 2 =