• Select (Yellow): Select DC/AC in current modes, continuity, diode, capacity, temperature in ohm mode and can also be used to show duty cycle in Hz mode and frequency and duty cycle in AC mode.
  • Hold: Will freeze the display reading, until pressed again, hold down to activate the background light.
  • Range, REL: Select manual range and change range, hold down to reactivate automatic ranging. In capacitance it is a REL function to zero out and offset.
  • Max/min: Capture maximum and minimum values, it will change between max/min/actual, holding it down will activate flashlight.

Rotary switch:

  • Off: Meter is turned off
  • VAC: AC voltage and frequency/duty-cycle, the frequency input has high sensitivity and low bandwidth.
  • VDC: DC voltage
  • Ohm, diode, continuity, capacitance, temperature Fahrenheit, temperature Celsius
  • Hz: Logical frequency input, can also show duty cycle.
  • A: Ampere DC or AC
  • mA: Milli ampere DC or AC
  • uA: Micro ampere DC or AC
  • Test: Phase detection with one connection. This will show 0 or OL in the display, OL means phase detected.
  • NCV: Non-contact voltage or electric field detection.
  • 10ADC: 10A DC current input.
  • COM: The common terminal for all ranges.
  • xxx: All other ranges, including uA and mA.



  • Volt and frequency
    • 1V AC readings is 5% down at 2.3kHz, rms will not work at that frequency
    • AC frequency range with 0.1V input is from 1.1Hz to 2.5kHz
    • AC frequency range with 0.1V input it can be stretched to 32kHz
    • AC frequency range requires a zero crossing.
    • Frequency input can handle +/-2.8V offset with 1Vrms input.
    • At 1Vrms frequency input range is from 1.1Hz to 44MHz
    • Duty cycle works from 1% to 99% at 100kHz with 4Vpp, precision is within 0.3.
    • Max/min needs about 200ms to capture a voltage, autorange is disabled when using this function and it will not capture every max/min.
    • Input impedance is 10-11Mohm on DC and AC
    • Frequency input is 2-3kOhm in input impedance above 2V
    • Input protection is 1000VDC/750VAC
    • Frequency input is protected to 250V or 550V DC or AC peak (Both values are specified).
  • Current
    • 10A range has audible alarm above 10A
    • 10A range is fused with a 10A/250V 5×20mm fuse
    • mAuA range is fused with a 0.6A/250V 5×20mm fuse
    • Current ranges starts in DC
    • Input voltage must not be more than 36VDC or 25VAC
  • Ohm, continuity, diode and capacitance
    • Ohm needs about 2.5s to measure 100ohm
    • Ohm voltage is 1.1V open and 0.25mA shorted.
    • Continuity is fast (About 20ms).
    • Continuity beeps when resistance is below 50ohm.
    • Continuity is 2.1V open and 0.25mA shorted
    • Diode range uses 4.0V, max. display is 3.3V at 0.25mA, max. current is 1.5mA shorted
    • 10uF takes about 2.5 seconds to measure.
    • 70000uF takes about 7 seconds to measure.
    • Overload protection is 550V DC or AC peak
  • Miscellaneous
    • Current consumption of meter is 1.6mA, 8.2mA with backlight, 9.1mA with backlight and 13.3mA with both.
    • Meter turns off at 2.2V, battery symbol show at 2.3V.
    • Readings will be correct until meter turns off.
    • Backlight fades with dropping voltage, but it usable until meter turns off.
    • Flashlight fades with dropping voltage, but it usable until meter turns off.
    • Viewing angle is good except from the top.
    • Display updates around 3 times/sec
    • Backlight will automatic turn off after about 12 seconds.
    • Flashlight will not automatic turn off, but turns off when the meter turns off.
    • Will automatic turn power off in about 17 minutes.
    • Standard probes cannot be fully seated in the meter, but they do connect (About 5mm stick up).
    • The meter usual need a few display update to before it display the value.
    • Weight is 209g without accessories, but with sleeve and battery.
    • Size is 145 × 70 × 37mm with sleeve
  • Probes
    • Probe resistance 46mOhm for one.
    • Probe wire is soft and 73cm long.


Additional information

Weight 0.1 kg


There are no reviews yet.

Be the first to review “ET8102 Digital Multimeter 6000 Counts True RMS Flashlight Digital Voltmeter 1000V 10A AC/DC Ammeter Pocket Multimeter in Pakistan”

Your email address will not be published. Required fields are marked *

seventeen + 3 =